Galvanized 2" Square Trailer Axle - 3,500 lbs. Capacity with 1 3/8" x 1 1/16" Spindles - 91.25" Hub Face

In stock

SKU F3596G
Price $441.00
Item F3596G
Approximate Overall Length 96"
Hub Face 91 1/4"
Capacity 3,500 lbs.
Brand Tie Down Engineering
Manufacturer Product # 49561

Description / Galvanized 2" Square Trailer Axle - 3,500 lbs. Capacity with 1 3/8" x 1 1/16" Spindles - 91.25" Hub Face

The F3596G (Tie Down Engineering/Dexter Marine part number 49561) is a 3,500 lb. capacity replacement trailer axle designed with marine environments in mind. The galvanized finish forms a coating of zinc which, when intact, prevents corrosive subtances from reaching the underlying steel or iron. Pressed stainless steel wear rings are present on the spindles to provide a tight, protected grease seal fit. The four hole flanges allow for brake installation. A pre-drilled 5/16" drain hole purges any water from the inner tube after submersion.

 

Product Features:

  • Hot dipped galvanized beam to combat corrosion
  • Galvanized axles will last much longer than painted ones and are perfect for marine applications
  • Features a stainless steel wear sleeve on either spindle
  • Straight axle design
  • Slight camber built into spindle welds
  • Used for leaf spring suspension systems
  • Includes 2 castellated nuts, 2 washers, and 2 cotter pins
  • Zerk fitting at end of spindles for simple and easy bearing lubrication
  • Pre-drilled 5/16" drain hole
  • 4-hole flanges for brake mounting
  • Hubs/drums sold separately

 

Product Specifications:

  • Capacity: 3,500 lbs.
  • Hub Face Measurement: 91.25"
  • Flange to Flange Measurement: 85"
  • Overall Length: 96"
  • Spring Center Range: 75.75" - 79.75"
  • Beam: 2" x 2" Square
  • Spindle: 1 3/8" x 1 1/16" Flared
  • Flange Hole Distance: 2 7/8" center-to-center

 

Hardware Information:

  • Inner Bearing (sold separately): 68149 (1 3/8" inner dimension)
  • Outer Bearing (sold separately): 44649 (1 1/16" inner dimension)
  • Grease Seal Inner Diameter: 1.72"

 

NOTE: This axle does not come pre-drilled for the springs to mount. It is recommended to use seats and to stay within the manufacturers spring center range to achieve the full capacity. Going inside or outside of the recommended spring center range may cause the strength of the axle to decrease. Square seats do not need to be welded to the axle. Drilled axles cannot be returned for any reason.

 

Tie Down Engineering/Dexter Marine of Georgia Part Number: 49561

Related Products

Fits 2" Square Axle - Trailer U-Bolt Kit - U-Bolts Zinc Plated - Plates Galvanized
$30.69
Fits 2" Square Axle - Trailer U-Bolt Kit - U-Bolts Zinc Plated - Plates Galvanized
$31.29
Axle Spring Seats (Galvanized) for 2" Square Axles
$4.90
5 Bolt on 4 1/2" Trailer Hub with 1 3/8" x 1 1/16" Bearings (L68149 & L44649)
$54.70
Dexter 10" x 2 1/4" Brake Drum - 5 on 4 1/2" with 1 3/8" x 1 1/16" Bearings (L68149 x L44649) - 1/2" Studs
$92.76
Dexter Marine/Tie Down Engineering 9.6" Integral Disc Brake Assembly - 5 on 4 1/2" - Galv-X Coated Rotors
$258.81
Tie Down Engineering 9.6" Single Axle Disc Brake Kit - 5 on 4 1/2" - Galv-X Coated Rotors
$906.59