Tie Down Engineering 9.6" G5 Series Single Axle Disc Brake Kit - 5 on 4 1/2" - Stainless Steel Rotors

In stock

SKU 82404
Price $1,191.67
Item 82404
Number of Bolts 5
Brake Manufacturer Tie Down Engineering
Manufacturer Product # 82404

Description / Tie Down Engineering 9.6" G5 Series Single Axle Disc Brake Kit - 5 on 4 1/2" - Stainless Steel Rotors

G5 stainless steel disc brake complete kit comes with everything needed to replace or upgrade from drum brakes to trailer disc brakes. Model 660 disc brake actuator features a cast ball clamp, Drop-N-Go auto coupler latch and over sized master cylinder, with solenoid installed.

Product Features:

 

Hub/Rotors

  • Pre-assembled with races, bearings, and grease seal installed
  • Pre-greased with Lucas Red 'N' Tacky grease
  • Integral, one piece hub and rotor combination
  • Stainless steel rotor provides the best protection against corrosion and rust
  • Galv-X coated hub
  • Triple lipped grease seal for an air tight spindle fit
  • Grease cap with rubber plug for easy access to axles with zerk fitting spindles when re-greasing

 

Calipers

  • Aluminum alloy a380 caliper with an E-coated finish
  • Slim design permits short axle overhangs and faster cooling
  • Automotive quality ceramic brake pads with stainless steel backing plates
  • Over-sized rubber boot is 50% thicker by design and provides positive piston withdrawal
  • Non-corrodible oil impregnated bronzed bushings
  • Type 304 stainless steel bleeder valves with Teflon coating
  • Fine thread, stainless steel slider pins
  • Rotating brake line connector

 

Mounting Brackets

  • Galv-X Finish
  • Fits on 4-hole 3,500 lbs. axle flanges

 

Brake Lining

  • Includes all lining for a single axle braking system
  • 20' main line
  • Brass tees
  • Clamps and ties included
  • Flexible rayon reinforced rubber lining

 

Actuator

  • Tie Down Engineering Model 660E
  • Cast ball clamp & extended latch lever
  • Zinc plated for protection
  • Built-in back up solenoid with cover
  • Heavy duty vinyl coated coiled emergency stop cable
  • "Drop N Go" coupler latch
  • Tongue mounting bolts not included

 

Product Specifications:

  • Rotor Diameter: 9.6"
  • Inner Bearing: 68149 (1 3/8")
  • Outer Bearing: 44649 (1 1/16")
  • Seal Inner Diameter: 1.72"
  • Bolt Pattern: 5 on 4 1/2"
  • Axle Rating: 3,500 lbs.
  • Actuator Coupler Size: 2"
  • Actuator Mounting: 3" wide trailer tongues
  • Actuator Capacity: 6,600 lbs.

 

NOTE: Brake pads must be replaced when 3/32" (0.94") or less of the pad friction material is left.

 

Includes:

  • (2) Complete hub/rotor assemblies greased with all hardware
  • (2) Mounting brackets with hardware
  • (2) Calipers with slider pins
  • (1) Complete single axle brake line kit with 20' main line
  • (1) Model 660E actuator

 

Tie Down Engineering/Dexter Marine of Georgia Part Number: 82404

Related Products

Tie Down Engineering 9.6" Single Axle Disc Brake Kit - 5 on 4 1/2" - Galv-X Coated Rotors
$906.59
Tie Down Engineering Caliper 46910 with Pads "G5" Series - Fits 3,500 lb. to 6,000 lb. Axles
$169.68